Men's waterproof sailing and rain jacket SAILING 100 Navy blue
Store Availability
Store Availability
BENEFITS
Resistance to salt water
Materials and zips resistant to salt water and sea air.
Warmth
Quilted lining (150 g/m2) provides very good insulation
Windproof
High neck and coated fabric to cut the windchill effect.
Waterproof
Moderate rain for 2 hrs 5,000 mm Schmerber (JIS standard) Pockets not waterproof
Pockets
Three secure pockets, including one inner pocket
Breathability
Very breathable coated fabric (RET < 12): reduces condensation
TECHNICAL INFORMATIONS
Waterproofing 1/2
We measure the fabric resistance to water pressure in mm of water column (based on the JIS standard). The higher the water pressure withstood by the fabric, the more waterproof it is.
On our warm Sailing 100 jacket:
Component is resistant to water pressure of 5,000 mm Schmerber (JIS standard). This equates to the average pressure applied by the water during a rain shower.
The anorak's waterproofness was tested in a rain shower with 60 litres of water/m²/hour for 2 hours.
Waterproofing 2/2
- High collar
- Injection-moulded plastic to avoid salt oxidation
- Water-repellent components (water runs off the fabric)
- 100% taped seams
- Central opening features a flap and underflap with a drainage channel for optimal waterproofing
Water repellency
A fabric is water-repellent when water slides off the surface of the fabric, without seeping in.
Your jacket does not become waterlogged and remains lightweight and breathable. The water-repellent properties are achieved with a treatment applied to the external side of the fabric, but in practice these properties can be altered.
The water-repellent properties can be reactivated by putting the jacket in a dryer for 10 minutes at the lowest temperature.
How to reactivate the water repellency
Drying is a crucial phase in reactivating the water repellent treatment.
We recommend that you lay your jacket flat on a clothes rack and leave it out to dry in the open. Caution: never dry your jacket directly on a radiator.
Then place them in the tumble dryer on a short synthetics cycle, i.e. 10 to 15 minutes, before turning it back the right way round. Caution: do not over-dry the garment.
Warmth:
The jacket is lined with 150g/m2 quilting on the body and 100g/m2 on the sleeves. This provides thermal protection and an incredible feeling of warmth (between -5 and -10 degrees
The jacket remains light (880 g in size L).
Hood
The hood does not pack down into the collar, it is attached.
Completely depth and height-adjustable hood with quilted lining (100 g/m2).
Visor to provide a good level of protection and a better hold.
The high neck effectively protects the neck.
pockets
Two zipped pockets on the front lined with fleece, guaranteed warmth.
One inside pocket on the left chest with rip-tab closure
WARNING: the pockets are NOT WATERPROOF
Jacket fastening
Use of a full-length zip with a padded outer flap and inner flap that provide protection from wind and water.
Breathability
To find out whether a fabric is breathable, we test its evaporate resistance or RET (ISO 11092 standard). The lower the fabric's resistance, the more moisture is evaporated, and therefore the higher the fabric's breathability.
We consider that if:
RET < 9 = highly breathable fabric
9 < RET < 12 = breathable fabric
The RET of the Sailing 100 jacket is breathable
composition
composition
Padding: 100.0% Polyester; Main fabric - Bottom: 100.0% Polyamide; Lining: 100.0% Polyester; Coating: 100.0% Polyurethane; Main fabric - Top: 100.0% Polyamide
Tips for storage and maintenance
MAXIMUM WASHING TEMPERATURE 30°C. NORMAL TREATMENT.
BLEACHING EXCLUDED.
DRYING IN TUMBLE DRYER POSSIBLE. LOW TEMPERATURE, MAXIMUM DRUM EXHAUST TEMPERATURE 60°C.
DO NOT IRON.
DO NOT DRY CLEAN.
TESTS AND WARRANTY
Warranty
2 Years
Our Ecodesign Approach
Our ecodesign approach reduces the environmental impact of our products.
We’ve examined the environmental footprint of this product in order to identify how we can produce it in a more sustainable way. With this knowledge, our design teams were able to develop this product while significantly reducing its environmental impact.
Sustainable design measures implemented on this product.
-
Environmental ImpactDesigned to reduce environmental impact
Product made with a CO2eq reduction of 56% compared to the previous or similar product
Our design teams are working to develop processes that will reduce the impact of a product, while preserving its technical characteristics. This reduction relates to the following indicators: climate change, air pollution, water pollution and resource depletion.
-
ProcessDope dyed
Product made from 30% dope dyed yarn
Using this mass-dyeing process enables us to reduce CO2 emissions linked to the production of dyed textiles by at least 17% compared to conventional dyeing.
-
MaterialRecycled polyester
Product made from 44% recycled polyester
Using recycled polyester rather than conventional polyester reduces the CO2 emissions linked to the material by at least 17%.
-
ProcessBiton
Product made from 16% yarn combining dyed and undyed fibres
Using this dyeing process enables us to reduce the CO2 emissions linked to the production of the dyed component by at least 39% compared to conventional dyeing.