Scuba Diving Octopus Braided MP Hose Hyperflex - Neon Yellow 100 cm
Store Availability
Store Availability
BENEFITS
Modularity
100 cm long neon yellow medium-pressure hose.
Robustness
Braided nylon outer coating for greater strength and suppleness.
Impact protection
Comes with two hose sleeves to protect the crimping.
TECHNICAL INFORMATIONS
Technical features
Length: 100 cm.
First-stage connection: 3/8 UNF male connection. Tighten with a 9/16 inch wrench (between European sizes 13 and 14). Second-stage connection: 9/16 UNF female connection. Tighten with a 11/16 inch wrench (between European sizes 17 and 18).
Hose composition
The base of the hose is made from antimicrobial thermoplastic polyurethane (TPU) polyether.
Outer coating: braided nylon for greater strength and suppleness. Withstands more twisting than conventional rubber hoses. Prevents the feeling that the regulator is pulling on the mouth.
What is the purpose of the medium-pressure hose?
The MP (Medium Pressure) hose, also called LP (Low Pressure), conveys the expanded air from the tank (compressed at high pressure) through the first stage and to the second stage of the regulator. The conveyed air is usually at a pressure of between 8 and 10 bar.
Tips on assembly
To not overtighten the first stage. First stages are usually made of chrome-plated brass, a soft alloy. Overtightening can damage the first stage. The O-ring on the hose is used for watertightening purposes.
On the second-stage connection, there is a cylindrical male part inside with an O-ring for watertightness.
Use a silicone grease to lubricate the seals and increase their lifespan.
Wear and replacement of the hoses
Repeated pressurisation of the regulator and external cracks will made the hose more fragile. This type of wear, usually invisible, affects the performance of your regulator. At the worst, your hose will end up by breaking, usually at the point where it is crimped.
Regularly check your hoses and replace them if cracked.
Replace your hoses at least every 5 years.
Servicing the regulators
SUBEA-TRIBORD advises you to service your regulator every two years and to make a visual inspection at least once a year. This two inspections must be made in a SUBEA-TRIBORD certified workshop.
A service is also recommended after a particularly intensive season (more than 100 dives), or after a long period of inactivity.
During this inspection, your hoses will be checked and replaced if necessary.
Taking care of regulators
Never use solvents or hydrocarbon-based products to clean or lubricate the regulator yourself. Never use spray cans, because the gas propellent can attack the plastic.
Use a silicone grease to lubricate the seals and increase their lifespan.
composition
composition
Protection cover: 100.0% Thermoplastic Polyurethane; Rivet: 100.0% Brass
Tips for storage and maintenance
Storage tips
It is important to store diving equipment away from sources that produce ozone. Keep your equipment in a dry place away from heat and direct sunlight.
Restrictions on use
Diving requires the certification of a certified instructor.
TESTS AND WARRANTY
Test product
Our technical partner: Planet Ocean (the PADI 5-star diving centre) based at the Water Sports Centre by Decathlon in Hendaye - France. The centre uses SUBEA diving equipment throughout the year.The team of instructors are rigorously involved in the development of our SUBEA products: from the design phase with the teams (product managers, designers and engineers), to the endurance tests with the help of the centre’s divers (from beginners to trainee instructors, all year long).
Warranty
2 Years
Agree by
All the SUBEA regulators were also developed through usability and convenience testing (static, dynamic and biomechanical analysis) conducted by DAN Europe, as a specialist and independent consultant. *DAN Europe (Divers Alert Network Europe) is an international non-profit medical and research organisation dedicated to the safety and health of divers.